DIY: How to Make a Roll Top Horse Jump

DIY How to Make a Roll Top Horse Jump

This project is a bit more complicated than the Jump Panels, but it is very doable. As with the panels, we use 8′ poles so we made two 3′ wide roll tops. If you’re making this for an official 12′ wide jump, you could either make three of them or make them 5′ wide each. I like them smaller as that way they weight less and are easier to move around.

Materials:
Four 2x6x10’ boards
Nine 1x3x6’ boards
Four 2x4x8’ boards
2.5″ #10 Wood Screws
2″ nails
4 Handles (optional)
Exterior paint and primer and a paintbrush.

You’ll also need a circular saw, C-clamps, a screwdriver, and a hammer.

Here’s a diagram to start off with:

DIY How to Make a Roll Top Horse Jump

1. Start by cutting your 2x6x10′ boards into four each of the following lengths: 27″, 26″, 23.25″, 17.75″

2. Take one of your 2x6x27″ boards and cut the one end on an angle so the board is 27″ on the one edge and 26″ on the other edge.

DIY How to Make a Roll Top Horse Jump

3. Use this board as a guide to mark and cut your three other 27″ boards. The following picture is from a different cut, but gives you the right idea. You want all 4 of your boards to be identical.

DIY How to Make a Roll Top Horse Jump

4. Next, cut one of your 26″ boards so that one edge is 23.25″. Use that board to mark and cut your three other 26″ boards.

DIY How to Make a Roll Top Horse Jump

5. Repeat the same process to cut your four 23.25″ boards down so that one edge on each is 17.75″:

DIY How to Make a Roll Top Horse Jump

6. The last board – the 17.75″ board – is the most complicated as you’ll need to make 2 cuts. First, measure 4″ out and 11″ up from the bottom left corner of the board. Put a mark at that spot (red star) and draw a line from the upper left hand corner through the mark (teal line). Cut that upper right triangle off first.

7. Then draw a line from the mark (red star) through the bottom right hand corner (green line) and cut that piece off second.

DIY How to Make a Roll Top Horse Jump

At this point you should have 4 of each board like so:

DIY How to Make a Roll Top Horse Jump

8. Now you’ll need to cut your 2x4s into four 21″ boards, six 32″ boards, and four 18″ boards and cut your 1x3s into sixteen 3′ boards.

DIY How to Make a Roll Top Horse Jump

9. Use some of your 1×3 boards and C-clamps to make a straight edge to line your roll top boards up against. This ensures they’re all even with each other. Make sure to lay out half the boards going one way and half going the other way. See the picture below. Then lay your 2x4x18″ and 2×4″21″ on top in the pattern below:

DIY How to Make a Roll Top Horse Jump

10. Screw the 2x4s onto the 2x6s using wood screws. Repeat until you have 4 roll top sides.

DIY How to Make a Roll Top Horse Jump

11. Face two opposite roll top side pieces and face them towards each other with the 2x4s on the inside. Screw two of your 32″ 2x4s onto the top and bottom as below:

DIY How to Make a Roll Top Horse Jump

12. Flip your roll top upright and add a third 32″ 2×4 as a back brace as seen below. We chose to use the extra 2×4 scraps (seen to the right of the roll top here) to add “feet” to this side of the jump making the roll top reversible. This way it can be laid down to make a wider 2’3″ tall roll top or placed up right for a steeper 2’6″ roll top. Repeat for your 2nd roll top base.

DIY How to Make a Roll Top Horse Jump

13. Get your nails and 1x3s and start by aligning one of the 1×3 boards with the top of the roll top. The board will stick out 2″ on each side of the roll top base. Nail the board in with two nails on each side and then add the next board pushing it flush against the first board.

DIY How to Make a Roll Top Horse Jump

14. Continue nailing until all 16 boards are wrapped around the roll top. Then repeat with your 2nd roll top base.

DIY How to Make a Roll Top Horse Jump

15. Paint your roll top. I chose to do three shades of brown, but I have seen some cute rainbow and other designs. I painted the poles with some green accents because I have green astroturf covers for the roll tops that attach by magnet. You could also stain the wood if you don’t want to paint, but you will need to do something to protect the wood if you want your jump to last.

DIY How to Make a Roll Top Horse Jump

Optional: Add handles to make them easier to carry and move around the arena.

** I’m not a professional jump builder or professional contractor. If you follow these directions, do so at your own risk. If you use any such jumps made from following these directions, do so at your own risk.

7 thoughts on “DIY: How to Make a Roll Top Horse Jump

  1. Liz

    Well done!! Always wondered about making these on my own. You’ve made me believe it’s possible! Great post.

Comments are closed.